100' MEDIUM DUTY LADDER

100' Medium Duty Ladder

Has the same features as our 75' Medium Duty Ladder but with added reach. These ladders can be used on smaller, lighter chassis.

Four (4) section, telescoping steel ladder constructed of high strength steel, certified to 70,000 psi
Aerial device mounted over the rear axle, on a torque box sub-weldment with rear stabilizers and with the ability to short-jack
Bolt-on egress with full 250 lb. rating

Ladder sections are trussed vertically and diagonally with round steel tubing
Environmentally sealed ladder sections to protect against corrosion
All ladder rungs are round and welded to each section in two places with K-bracing for rigidity
Ladder sections are designed with adequate hand spacing and room for vertically mounted cable tracking, resulting in unobstructed egress on ladder
Fold down steps standard at tip
Rungs are sheathed with an aggressive composite luminescent rung covers to increase visibility during egress and do not need electrical connections or amp draw
Extension and retraction motion by dual hydraulic powered cylinders and cable pulley system
Rotation motion through a 46" swing bearing/spur gear, driven by one (1) planetary hydraulic motor
Elevation motion through (2) double acting, lift cylinders (5 deg below horizontal to 80 deg above)
All cylinders designed with integral holding valve cartridges in the event of a hydraulic line failure
Rotational brake applies when pressure control is released

72" long x 80" wide turntable is constructed of with a steel support framework covered with Morton Cass aluminum surface, with an aluminum treadplate perimeter
Access to the turntable is from rear body stair wells, one on each side of the truck
Stairs are lit by two lights activated by the aerial master switch
Includes control console and space for hydraulic and electrical components

One turntable control station located on driver side
Aerial controls are direct hydraulic, fully proportionate
Hydraulic load sensing piston pump, capable of multiple-function operation without speed loss
High pressure hydraulic manifold block, with test ports
Pressure and relief filtration system
Hydraulic reservoir of 38 gallons
Relief valve set at 3,150 psi to protect hydraulic system components
12V emergency power unit (EPU) with 30-minute run time, capable of stowing the ladder in the event of a power loss

Water swivel 4 inch capable of 360 degree rotation
Telescoping anodized aluminum waterway capable of 1,000 gpm
4.5" dia. base waterway pipe
4" swivel capable of operating between -5 degrees and up to 80 degrees
A 250 psi pressure relief valve located below the torque box
Aerial monitor (electric), capable of 1,000 gpm, Akron self-stowing monitor (standard)
5" rear inlet to the aerial waterway

Atkinson communication system between the aerial tip and the turntable console, with optional 3rd station at pump panel
Master control at the turntable with push button talk and volume control
Self contained "hand-off' speaker/mic at the basket
Electrical System
Electrical swivel capable of 360 degrees with 28 collector rings, each capable of 20 amps
Four (4) 12V unity lights standard, two at tip, two at base
110V electrical system, one (1) 20 amp NEMA L5-20, 3-prong water proof receptacle (optional)

Side compartments integral assembly with the rear fender
Neoprene elastomer isolators will isolate chassis movement from the body structure
Bodies are formed and welded construction for durable, long lasting design without the unnecessary weight
Exclusive Pierce underslung steel body supports featuring 3-point isolated mount system. This reduces torsional stress and road shock from being transmitted into the body. The underslung design prevents compartment floors from sagging after years of use.
Aluminum extruded rub rails, bolted on for easy repair
Galvaneal steel, stainless steel, high-strength aluminum
Interior of all compartments are painted with multispec to hide dirt, abrasions, and protect from oil, gas, and hydraulic spills
Automotive-style hinged doors constructed with double pan, double seals, enclosed latches, and .25" hinge pins
Roll-up doors with lifetime warranty (available in satin or painted finish)
Handrails are Pierce's exclusive "cross knurled" design to reduce hand slippage